Auction Archive

 About this site
 Wanted to buy

bulb gallery

drawn tungsten
coiled tungsten
mini tungsten
pressed tung.
figural bulbs
christmas sets

neon lamps
argon lamps
xenon lamps
special mercury

plugs & fittings

tube gallery

 Box art

museum pics

 Dr. Hugh Hicks
Fort Myers, FL.


 Related links
 Submit a link


Author Topic: Incandescent Bulb Life Times  (Read 15950 times)

Offline Anders Hoveland

  • Jr. Member
  • **
  • Posts: 21
Incandescent Bulb Life Times
« on: August 30, 2013, 02:32:10 pm »
With incandescent bulbs, in general, there is a trade-off between light output at a given wattage and how long the bulb lasts until it burns out. But I have also noticed that some light bulbs were designed to last much longer than others, without any sacrifice in efficiency in comparison. So there must be other factors besides just the filament thickness. I am wondering whether the quality of the filament has anything to do with it. There is also a rumor that in recent years GE and Phillips were allowing traces of air into the bulb to intentionally cause premature failure, so consumers would have to buy more bulbs. One accusation is that they did this as part of their intense effort to convince politicians/consumers that the old bulbs should be phased out in favor of the new "longer lasting" lighting technologies. They seem to have stopped manufacturing their more expensive "long life" light bulbs around the same time they began lobbying for the phase out.

 Another possibility is that some of the "long life" bulbs simply had a higher lifespan rating because the filament has supports. But would this not only affect the lifespan if the light bulb was being exposed to vibration? How could filament supports increase the life span if the hot filament was not being agitated in some way? And how much can filament supports really extend lifetime, if this is the case? Something else I have been wondering is whether some of the bulbs were actually being filled with krypton gas, instead of the usual argon-nitrogen mix. Perhaps the manufacturers simply did not bother to mention this fact, as it was too technical for consumers to understand, or perhaps the technical details of the bulb was considered something of a trade secret the company did not want to be advertising to its competitors. Krypton gas typically offers the most benefit for bulbs rated under 40 watts. For a 100 watt bulb, the addition of krypton can improve the efficiency of the bulb by 4% and extend the filament life by around 50%. Krypton is also more expensive than argon, not by much, but it could significantly increase the cost of such an already inexpensive bulb (0.25-0.50 USD). Obviously a biger light bulb requires more gas than a smaller flashlight bulb. A standard sized A19 industrial krypton light bulb could be bought for 2.75 USD.

 I have a package of 100 watt Sylvania light bulbs rated 1500 lumens with a 1500 hour rated lifespan.
 I also have another package of 100 watt light bulbs (from another company) also rated 1500 lumens, but with a 2000 hour rated life span.
 It seems one is no longer able to by these bulbs anymore. All the 100 watt light bulbs being sold the year before the phase out (when all the 100 watt bulbs dissappeared from store shelves) only has a rated lifespan of 750 hours! And I can state from experience that they also seemed to burn out very fast in my home. Good thing I have a stash of the old light bulbs tucked away.

 I am also wondering whether the new halogen bulbs are really much of an improvement over the old light bulbs. As I mentioned, there is a trade-off between efficiency and lifespan. A typical "100 watt replacement" halogen manufactured by Sylvania is 72 watts, rated at 1480 lumens, and a 0.9 year (983 hours) lifespan. The "double life" version by the same company (also 72 watts and still claiming to be a 100 watt replacement) is somewhat less bright, rated at 1280 lumens and 1.8 years (1965 hours). Sylvania does not make any higher wattage long life halogen bulbs. In fact 72 watts is the highest wattage they manufacture a standard A19 sized bulb now. Bulbrite, however manufactures a 95 watt halogen with a 2000 hour rated life span. The company explicitly advertises that the capsule is filled with xenon (which is even better than krypton), so one would expect this bulb to have the highest efficiency for its given life span. It is rated 95 watts, 1600 lumens, 2000 hours. (the bulb is not in the shape of a standard pear-shaped A19, but rather in the shape of the old BT15 halogen double enveloped bulbs). This is a premium halogen bulb being sold for over 3.50 each.

 But the efficiency of this 95 watt xenon halogen bulb is 16.8 lumens per watt, while the old 100 watt bulbs I have are 15 lumens per watt, both at the same life span. In other words this premium extra-efficient halogen bulb is only 12% more efficient than the old good quality incandescent bulbs. Is it worth it? In other words, if we simply took a good quality normal incandescent bulb that consumed 72 watts of power, and gave it a thinner filament to incandesce at a higher temperature, it should be able to give off 1302 lumens of light and last for nearly 1000 hours. Again, I am wondering whether these 100 watt bulbs I have were filled with krypton, or possibly whether the propaganda from the big 3 lighting companies are overexaggerating the inefficiency of the old incandescent bulbs.

 Just for anyone who is wondering, I bought a pack of krypton traffic bulbs a while back. They are rated at 116 watts, 8000 hour lifespan, and 1260 lumens. So incandescent bulbs certainly can be made to last much longer. One would think with such a long-lasting bulb the light would be very yellowish because of the lower temperature, but surprisingly the color temperature is rated 2850K, which is a little higher even than some halogen bulbs.
UPDATE: I have tried these bulbs, and it seems their actual color temperature is lower, about the same as a 130v rough service bulb being used in a 120v outlet, just a little too yellowish for my preferences. I guess that is to be expected. You can't expect an 8000 hour lifetime from an incandescent bulb without some tradeoffs, apparently.

 If you have a difficult to reach lamp fixture on a high ceiling in your living room, and really want the excellent quality of light from incandescent bulbs, these traffic bulbs may be an option to consider, if you are willing to pay the higher electric bills over many years. Of course, this might not matter so much if you live in a cold climate, since you will just be paying for extra heat. (a little advice if you want to buy one, be sure you get one with a rated voltage that exactly matches your outlet voltage, most of the traffic bulbs are rated at a slightly higher voltage, and this will significantly decrease both power consumption and light output, and make the light more yellowish)

I believe the color temperature of the incandescent bulbs most people have come to regard as "normal" is 2750-2850 K.
 However, some Americans may now be using 130v rated bulbs without realising it, in which case the color temperature would indeed be a more yellowish 2700 K.

Electronic Formulas and Calculations

 The total power consumption of an incandescent filament is inversely proportional to the resistance. W= 1/r
 A higher wattage bulb has a thicker filament. Keeping the resistance constant, a shorter length and thicker filament means higher temperature.

 Some of you might be wondering why a regular wire does not get incredibly hot, since it is designed to have minimal resistance. The answer is that the current it carries is only a fraction of what it could potentially carry. If the wire was attached to large enough supply of electric current, it would indeed act as a heat filament. Ordinarily, wires are only connected to a complete ciruit through a current limiting load, such as the filament in a light bulb. Furthermore, as the tungsten filament is heated, within a fraction of a second its resistance increases to around 15 times the resistance value when cold. (another smaller factor is that tungsten has twice the resistance of aluminum used in the wire) So, theoretically, any given length of wire should be releasing 1/30th the ammount of heat that a similar length of the incandescent filament is releasing. We do have to remember that the tungsten filament in a typical incandescent lightbulb is a double coil, and the actual length is quite long, a whole 2 meters in a 60 watt bulb! So, if we used 60 meters of wire to connect our light bulb to the power source, both the light bulb and wires would be giving off the same ammount of heat! It is no wonder then higher voltages are used to distribute electric power in power lines, as power losses are proportional to the the current, and that is keeping the wattage constant, since the increasing voltage does not increase losses. (it is the square of the current if we are just calculating heat generated taking into account volts and amperage).

 Here is one calculation that says a 100 foot AWG extension cord itself consumes about 20 watts of power in heat losses if it is powering a 600 watt load:

 There is also voltage drop to be considered. Making a conducting wire thicker will reduce its resistance and reduce how much voltage it consumes relative to the primary load.
 For example, if we have a 10v power supply, wires with a total resistance of 2 ohms, and a load with a resistance of 3 ohms, the total current able to flow through will be 10/5 = 2 amps, and then the voltage drop in the wires will be 2x2 = 4v, so there will only be a potential of 6 volts left across the primary load. Doubling cross section area (thickness) of the wire would cut the resistance in half to only 1 ohm, and then the voltage drop in the wires would be only 2 volts. This would mean less heat wasted in the wires.

So in conclusion, the wattage of an incandescent bulb is determined by the resistance value of the filament. A filament can be made thicker, but it also has to be made longer to maintain the given resistance value. A longer filament means the heat is spread out over a larger area and means a decrease in filament temperature. This will lead to longer lifespan because the tungsten will evaporate off the hot filament at a slower rate, and it will take more time for the evaporation to lead to eventual rupture, because the filament is thicker.
« Last Edit: August 30, 2013, 02:54:12 pm by Anders Hoveland »

Offline Anders Hoveland

  • Jr. Member
  • **
  • Posts: 21
Re: Incandescent Bulb Life Times
« Reply #1 on: August 30, 2013, 02:38:56 pm »
I have been trying a number of different types of bulbs, and I have found that some of the halogens are a little too glaring, with what seems to me to almost be an off greenish tint, while some of the regular incandescent bulbs are too yellowish and dull. Obviously all this has to do with the temperature of the filament. So I decided to make an inventory of some of the bulbs that I have:

lumens/watt color   lifetime
1300/ 75       17.3 H 3000
1490/ 72       20.7 H 1000
1300/ 71       18.3 H 2000

lumens/watt  color    lifetime
1220/ 75        16.3 -- 750  
1135/ 71        16  --   750
1020/ 71        14.4 -- 1125

 The "H" indicates that it is a halogen bulb (all the bulbs look the same, but the halogens have a little fused quartz silica capsule inside). The lifetimes are in hours. The lumen per watt efficiency correlates with the color temperature (although it is not exactly a linear relationship). Obviously, the "less efficient"/lower temperature the filament, the longer it will last, while halogen will increase the lifetime regardless.

 My favorite color temperature is from the 1135/71 watt bulb. I am guessing it is around 2800 K. Most of these color temperature ratings are not very exact, or accurate, so I found it useful to use the efficiency as the best quantitative indicator of color temperature. Obviously, what would make the most sense for me is to have long life halogen bulbs, but unfortunately these seem to be much more expensive than either the long life regular incandescents or the lower life halogens. The 750 hour bulbs are very inexpensive, so it makes more sense to stock up on these.

 I have also noticed that several of the bulbs I have bought have overexaggerated their lumens (though perhaps not intentionally), especially the very long lasting bulbs. I have some 100 watt incandescent bulbs that are labled 2000 hours, 1500 lumens on the packaging. They are more yellowish than most people would prefer, and I suspect the actual light output is closer to 1275 lumens (it is comparable to a regular 85 watt bulb). The lesson here is that, while regular light bulbs are available with long lifetimes, their light is just too yellowish, which is probably one of the reasons they have rarely been sold. The long-life halogens probably did not make economic sense for most people, since they were significantly more expensive (holding color temperature and efficiency constant). With halogen bulb prices having fallen due to larger scale production, they are now only 4-5 times more expensive. Assuming they made long life halogens at the same price of all the cheaper "energy efficient" halogen replacement bulbs, for people that preferred an intermediate color temperature, the overall costs would be about the same either way, although with the halogen they would not have to bother replacing the bulbs as frequently.
« Last Edit: August 30, 2013, 02:52:07 pm by Anders Hoveland »