research
 Patents
 Books
 Literature
 Articles
 Timeline
 Auction Archive

about
 About this site
 Wanted to buy

bulb gallery

Incandescent:
C
carbon
WD
drawn tungsten
WC
coiled tungsten
WM
mini tungsten
WS
pressed tung.
FG
figural bulbs
XL
christmas
XS
christmas sets
T
tantalum

Discharge:
NE
neon lamps
AR
argon lamps
XE
xenon lamps
MA
mercury
MC
fluorescent
MS
special mercury

Hardware:
F
fuses
FX
fixtures
PF
plugs & fittings
SA
sockets
SW
switches

tube gallery

 X-ray
 Geissler
 Crookes
 Radio
 Box art

museum pics

 Dr. Hugh Hicks
 
Fort Myers, FL.
 S.Slabyhoudek

links

 Related links
 Submit a link

 

Author Topic: Mini Bubblers  (Read 39535 times)

Offline Hemingray

  • Hero Member
  • ****
  • Posts: 136
  • Lightbulb Junkie
Re: Mini Bubblers
« Reply #15 on: August 12, 2012, 04:21:19 pm »
certainly you could come up with an adapter cord that has a diode in series with the set, should give you around 120VDC half-wave...I've done this on some of my older sets to dim and extend the life of the bulbs a bit. Not sure how that would work out with 230V/50Hz, you may notice an annoying flicker.

Offline adam2

  • Hero Member
  • ****
  • Posts: 108
Re: Mini Bubblers
« Reply #16 on: August 14, 2012, 03:53:44 am »
I would strongly advise against use of a 120 volt string of lights from 230/240 volts by means of a rectifier diode.
Whilst one might expect that this would give a 120 volt equivalent supply, this is not the case in practice.
Any 120 volt lamp, or series string of lamps, will be significantly overun if connected to 240 volts via a diode.

Anyone who doubts this should try a very simple experiment.
Obtain 3 similar 240 volt GLS lamps.
Connect two in series to the mains, and connect the third lamp to the mains via the diode.
The lamp on the diode will not light at full brightness but it WILL be significantly brighter than the ones in series.

The use of 240 volt lamps, or series strings totalling 240 volts, from a diode is fine.
The effective voltage is appreciably less than 240 volts and the lamp life thereby extended.

To use 120 volt strings in the UK the best way is via a 110 volt building site transformer.

This will slightly extend the lamp life as the output is 110 volts rather than USA 120 volt mains.
The fact that these transformers have an earthed center tap gives a useful extra factor of safety, the worst electric shock that you can get to earth is 55 volts, which is not normally dangerous. Still take though, just in case !


Offline Justin

  • Jr. Member
  • **
  • Posts: 37
Re: Mini Bubblers
« Reply #17 on: September 09, 2012, 12:26:35 am »
If you're afraid of those converters, get a good center-tapped autotransformer, some gfci's, and a few other parts and make a step-down transformer.

Offline Christmas Lamp

  • Purple Bubble Light
  • Hero Member
  • ****
  • Posts: 267
Re: Mini Bubblers
« Reply #18 on: September 09, 2012, 05:04:29 am »
I Have One Conveter and Only One Set {I Have 2} going at a time and Not for Long or I have Bubbler Night Light going and Again Not for Long....
So for the amount of Usage Mine Gets it Will be OK, Right?

Hope That Makes Sense....
I love Any Bulbs be They the Light up kind or the kind that Grows!!!

Offline adam2

  • Hero Member
  • ****
  • Posts: 108
Re: Mini Bubblers
« Reply #19 on: September 10, 2012, 05:26:29 am »
A properly made converter sold for the purpose of operating 110/120 volt appliances from a 220/240 volt supply should be OK.

My cautionery remarks reffer to the suggestion that a 120 volt string of lights could be worked from a 240 volt supply by means of a diode. This I consider to be most unwise for the reasons already given.