research
 Patents
 Books
 Literature
 Articles
 Timeline
 Auction Archive

about
 About this site
 Wanted to buy

bulb gallery

Incandescent:
C
carbon
WD
drawn tungsten
WC
coiled tungsten
WM
mini tungsten
WS
pressed tung.
FG
figural bulbs
XL
christmas
XS
christmas sets
T
tantalum

Discharge:
NE
neon lamps
AR
argon lamps
XE
xenon lamps
MA
mercury
MC
fluorescent
MS
special mercury

Hardware:
F
fuses
FX
fixtures
PF
plugs & fittings
SA
sockets
SW
switches

tube gallery

 X-ray
 Geissler
 Crookes
 Radio
 Box art

museum pics

 Dr. Hugh Hicks
 
Fort Myers, FL.
 S.Slabyhoudek

links

 Related links
 Submit a link

 

Author Topic: melted electrode in mercury lamp  (Read 16418 times)

Offline mr_big

  • Sr. Member
  • ***
  • Posts: 84
melted electrode in mercury lamp
« on: February 17, 2005, 03:46:52 pm »
OK I don't know how this happened but the starting electrode in my new Sylvania 1000 watt mercury lamp has melted I turned it on it ran for a few seconds and then the breaker blew any ideas on this one

Offline pSlawinski

  • Sr. Member
  • ***
  • Posts: 91
  • Westinghouse Lamps
    • Metal-Halide.net
Re: melted electrode in mercury lamp
« Reply #1 on: February 17, 2005, 09:44:19 pm »
1) Did you run this on a ballast?  (If your answer is NO then you killed it by over driving it)

2) If you did run this on a ballast how old is it?  Your ballast could be dead, and I would not suggest running any other lamps on it.

Offline mr_big

  • Sr. Member
  • ***
  • Posts: 84
Re: melted electrode in mercury lamp
« Reply #2 on: February 18, 2005, 11:14:15 am »
I did run this on a ballast and the lamp is brand new
I have a fefw extra that are really heavily used but still start easily
I will have to try one of them to see if it happens

Offline pSlawinski

  • Sr. Member
  • ***
  • Posts: 91
  • Westinghouse Lamps
    • Metal-Halide.net
Re: melted electrode in mercury lamp
« Reply #3 on: February 19, 2005, 09:37:21 pm »
What condition is the ballast in?  How many devices are on the circuit you ran that lamp on?

Offline mr_big

  • Sr. Member
  • ***
  • Posts: 84
Re: melted electrode in mercury lamp
« Reply #4 on: February 23, 2005, 11:22:24 am »
this is the only thing that I have on this circuit I don't think the ballast is bad because the other lamps that I ran on it worked fine
One of the lamps that I had a clear Sylvania 1000 watt mercury lamp did not work because it was heavily used and the arc tube was completly black it was because it was running in a fixture on a tree that was covered in ivy so I could not see the lamp
I have checked the wiring and voltage in my house and it is 120 wolts AC So I don't think it could be that

Offline pSlawinski

  • Sr. Member
  • ***
  • Posts: 91
  • Westinghouse Lamps
    • Metal-Halide.net
Re: melted electrode in mercury lamp
« Reply #5 on: February 23, 2005, 11:52:26 am »
The only thing I can think of that would cause the starting electrode to fail immediately would be a ballast failure.  As for your circuit breaker popping that could be from the ballast drawling more current after being turned on.  I have run my 1000W ballast on the same circuit as my computer, which is plugged into an uninterruptible power supply (UPS).  Immediately after plugging in the ballast the UPS beeps as if the power had been cut or there was a brown out.  If the circuit you run your ballast on is on a 10A breaker it is possible that the higher current drawl right after starting could be to blame for your breaker popping.  A 1000W ballast drawls ~8.333A during normal operation.  I'm not sure what the current drawl is during startup, but I believe it would be higher than 8.333A.

I guess you could also just have a bad lamp. Did you say the starting electrode was completely melted, or just slightly?  As far as I know Osram Sylvania mercury lamps are not particularly know for their quality...

Offline mr_big

  • Sr. Member
  • ***
  • Posts: 84
Re: melted electrode in mercury lamp
« Reply #6 on: February 23, 2005, 03:40:01 pm »
the starting electrode was completly melted
I know about the breaker it was a new 20 amp breaker I just replaced my entire panel because my old one got ripped off the wall by a tree

Offline pSlawinski

  • Sr. Member
  • ***
  • Posts: 91
  • Westinghouse Lamps
    • Metal-Halide.net
Re: melted electrode in mercury lamp
« Reply #7 on: February 23, 2005, 04:35:28 pm »
Hmmm, can you get some pictures of the lamp and post them here?

Offline mr_big

  • Sr. Member
  • ***
  • Posts: 84
Re: melted electrode in mercury lamp
« Reply #8 on: February 24, 2005, 11:22:21 am »
here are the pictures of the lamp the outer envelope has accidentaly broken
« Last Edit: February 24, 2005, 04:09:16 pm by mr_big »

Offline James

  • Hero Member
  • ****
  • Posts: 169
    • www.lamptech.co.uk
Re: melted electrode in mercury lamp
« Reply #9 on: February 24, 2005, 12:46:13 pm »
I have seen something similar in 700W lamps recently supplied by Osram, two out of ten of them failed after 400 hours.  Osram transferred all mercury production to China last year and while most are excellent, I have seen problems with the higher wattage types.

Best regards,

James.